Trailer Fender Recommendation for Tire Size 30x10.5R15

Question

Question:

Building my own trailer and have no idea how to measure out which fenders I would need. Its going to have 30x10.5R15 wheels on it. Trailer is 5x8.

asked by: Travis

0

Expert Reply:

For a fender that will fit your tire size well we have the part # HP29VR. This fender measures 32 inches in length, 10-3/4 inches in width and is 15-1/4 inches in height. It would basically be just a bit wider and longer than your tire size so it would be a nice fit.

expert reply by: Jameson C

0

Answer 1

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 2

The deflection (or amount the suspension can travel), for the Timbren part #A35RD545E that you referenced is 1-3/4 inches. I attached a picture that shows this dimension as well.

view full answer...

Answer 3

The deflection or amount of travel for the Timbren Axle-Less Suspension System #A20RS545 is 1-3/4 inches. The pictures on the product page will be updated.

view full answer...

Answer 4

Trailer magnets are not polarity sensitive. You can run either wire as power or ground and you'll be fine.

view full answer...

Answer 5

The Timbren Axle-Less Suspension, #ASR35HDS02, are designed to be used with 12 inch brakes. Timbren does offer an axle set #ASR3500S06 that will allow you to install 10 inch electric brakes. These axles are rated a 3,500 lbs, but do not have the…

view full answer...

Answer 6

While we don't currently carry any black fenders that would match your 2018 Forest Rover R-Pod RP-179 fenders we do offer the CE Smith Single Axle Trailer Fender #CE17900G which can be painted black and mounted onto your trailer.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Trailer Fender Recommendation for Tire Size 30x10.5R15

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching