Recommendation to Move Leaf Springs to Top of 3 Inch Axle on Trailer

Question

Question:

I need a kit to relocate my 3 inch axels from on top of the leaf springs to under my springs due to pulling the trailer with a lifted truck.

asked by: John K

0

Expert Reply:

We have exactly what you need!

To move the leaf springs on your trailer to the top of the axle, you will want the Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00. This is designed for 3 inch axles and for use with double-eye springs only. This kit will lift your trailer the height of the axle and leaf spring stack, making it easier to tow level with your lifted truck.

I have attached a short video demonstration along with the written installation details that you can also check out.

expert reply by: Chris R

0

Answer 1

The Over-Under Conversion Kit you mentioned, part #K71-385-00 is compatible with a 3 inch diameter axle, and would work fine with a fifth wheel camper. For two axles, you would need two kits. Keep in mind that in raising the trailer, you will be…

view full answer...

Answer 2

You are correct in the fact that you may get a little bit of room with taller tires but it really won't be a whole lot. When it comes to using an axle flip kit I wouldn't be too concerned about the shifting weight from the horses in the…

view full answer...

Answer 3

Yes! We have exactly what you need to move your axles so that they are under your leaf springs. If you have 2-3/8" diameter axles use part #K71-384-00 or you can use part #K71-385-00 for 3" diameter axles. These will raise your trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 12

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Recommendation to Move Leaf Springs to Top of 3 Inch Axle on Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching