Measurements for Curt Trailer Hitch C11496

Question

Question:

Hello, could you please tell me the measurement of this hitch?

asked by: Hiroaki M

0

Expert Reply:

I went out to the warehouse and took some measurements of Curt trailer hitch # C11496 for you. I have included a picture showing the measurements that I took.

expert reply by: Michael H

0

click to enlarge

Answer 1

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 2

The hitch you were looking at, part #C11496, is not really visible unless you are about eye level with the hitch. The cross bars are swept back to tuck them underneath the vehicle. I have included a link to the instructions that will show you the…

view full answer...

Answer 3

There seems to be some sort of mix up because trailer hitch #C11085 is designed to fit the 2011 to 2014 Acura TSX Sport Wagon, not the sedan. The proper hitch for a 2010 Acura TSX sedan is #C11496. And it does appear to stick out a bit as you can see…

view full answer...

Answer 4

As a large portion of the hitch will be visible below the rear bumper fascia, I would recommend the Curt Class I Receiver hitch, part #C11496. The hitch crossbar is constructed of round tubular steel, instead of the square tube like the other…

view full answer...

Answer 5

Yes, the Curt hitch, part #C11496, can be used on your 2010 Honda Accord with Dual Exhaust. You will have to temporarily undo a portion of the exhaust to install the hitch, but once the hitch is in the exhaust is put back into place. You will need to…

view full answer...

Answer 6

I spoke to my contact at Curt and he gave me a way for you to determine the distance the Curt Hitch part #C11496 would have from the top of the receiver opening to the ground. If you measure from the portion of your vehicle where the hitch attaches…

view full answer...

Answer 7

In order to satisfy Curt warranty requirements, any of their Class I or II receivers (like the C11423 you referenced) as well as a few of their Class III hitches must be used with a stabilizing strap like part #18050. This applies to any non-trailer…

view full answer...

Answer 8

I've linked you to product demonstration videos of all three bike racks. The best of the three racks will depend on the features you're interested in and which features you find most important. First some similarities. All three racks are…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Measurements for Curt Trailer Hitch C11496

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching