Recommended Power Adapter Plugs for 30 Amp Generator Plug to 50 Amp Welding Plug

Question

Question:

I am needing an adapter plug for a 30 amp 4 blade male generator plug to a 50 amp 3 blade welding plug?

asked by: Bill L

0

Expert Reply:

For your generator, I recommend the Mighty Cord Generator Adapter for RV Power Cord - 50 Amp Female to 30 Amp Twist Lock Male - 12" # A10-G30450VP and then the Power Grip 90-Degree Locking Marine-Style Power Cord Adapter - 50 Amps - 18" Long # CAM55562. If this is not the welding plug you are referring to, then we most likely don't have an adapter that will work.

expert reply by: Jason S

0

Answer 1

For the 3 prong 30 amp outlet on your generator, I recommend using the Power Grip Generator 30 Amp to 50 Amp RV Power Cord Adapter #CAM55412. The 3-Prong twist-lock design will connect with the outlet on the generator and the female end will connect…

view full answer...

Answer 2

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 3

To determine the best landing gear option for your 1997 Forest River Sierra you'll need to measure the where your weld-stops sit to see if there is a matching set so that you can swap over without having to cut off the old mounting brackets and…

view full answer...

Answer 4

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 5

From what I can see the 120-240v port on the Honda EUY7000is generator is a twist lock port so the Furrion RV Power Cord Adapter - 50A Female to 30A 4-Prong Male #FP52GEN4RSB is a compatible fit.

view full answer...

Answer 6

The 15,000 Btu Furrion Chill HE AC like the part #FR23PV does indeed have a start capacitor. In regard to the starting power needed, I reached out to Furrion, who told me the 15,000 Btu Chill AC's require 30 amps and 2,500 starting watts. So that…

view full answer...

Answer 7

I am not sure which Honda Generator you have but the Mighty Cord Dog Bone RV Power Cord Adapter part #A10-1550 will work for you if you have a 50 amp service on your trailer and a 120 volt outlet on your generator. That said, most generators use a…

view full answer...

Answer 8

There are a few different 50 amp style connectors. The ones for RV applications use the 240 volt twist lock style of 50 amp outlet (NEMA L6-50) a lot which has three prongs whereas the 120 volt style of 50 amp connector you are thinking of that has 4…

view full answer...

Answer 9

Using the Honda generator to power your RV is a great idea. You can use either outlet to power your RV. For any appliances that use less than 125V of power, I would recommend you use the 3 prong 30 amp outlet with a 50 amp adapter like the Camco…

view full answer...

Answer 10

The Mighty Cord 90-Degree Detachable RV Power Cord w/ Locking Ring and LED - 50 Amps - 25' #A10-5025ED90 is what works with almost all RVs. The center grounding pin is not typical. If you send me a photo I may be able to help, but most of the…

view full answer...

Answer 11

Thank you for the photo as it was very helpful and we do have exactly what you need to connect the 50 amp inlet on your trailer to the 110 volt on your house. Since there isn't a single adapter you will need two different parts, though using them…

view full answer...

Recommended Power Adapter Plugs for 30 Amp Generator Plug to 50 Amp Welding Plug

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching