Does Draw Tite Hitch 65028 Fit 2003 Chevy Silverado 2500

Question

Question:

I measured the Hitch Draw Tite #65028 that I purchased through Amazon and it measures 28 3/4. I have to return but im hesitant to buy another one

asked by: Jo L

0

Expert Reply:

The dimensions of the Draw Tite hitch part # 65028 are designed to perfectly match the frame that you have on your 2003 Chevy Silverado that measures 28-1/2 inches. I confirmed this with Draw Tite. I also attached an install video that shows it installed on a truck just like yours.

expert reply by: Jameson C

0

Jo L.

9/19/2017

I measured the Hitch Draw Tite #65028 that I purchased through Amazon and it measures 28 3/4. I have to return but im hesitant to buy another one

Reply

Jameson C.

9/19/2017

What it sounds like happened with the previous hitch you bought is that the brackets bent slightly in shipping. Sometimes hitches can get slightly bent during shipping and this can be fixed by bending the hitch back into place as long as the hitch only has a slight bend to it. If yours isn't lining up I can almost guarantee that is what happened. Some people will use open steps for leverage, vices and even car jacks to apply controlled force to bend the hitch back. You will want to look for flaking paint and physical stress marks on the hitch before and after you attempt to bend the hitch back. If you see any of those signs on the hitch you should not use the hitch on your vehicle as it has been fatigued to the point of not being safe to use.

Reply

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Does Draw Tite Hitch 65028 Fit 2003 Chevy Silverado 2500

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching