Choosing the Right Curt Class II Euro Style Ball Mount to Tow a Trailer Level

Question

Question:

Inside top of my receiver to grounbd measures 13inch and the top of my trailer couple measures 16. I want a Curt Euro draw bar, 2inch ball, 1 1/4inch receiver. Dont mind being a bit above level. Not hauling much over 600 lbs in a single axle 4foot x 6inch enclosed 900 lb trailer w/3000 axle. Am I looking at the right drawbar?

asked by: Pat C

0

Expert Reply:

If you are measuring to the top of the coupler then I will have to ask for the measurement to the bottom of the coupler instead. This is because the coupler covers the ball so the measurement to the bottom of the coupler provides a more accurate representation of what kind of rise or drop is needed to tow a trailer level.

I am willing to bet that the measurement to the bottom of the coupler will have you at just about level. That would make the best Curt Euro-style ball mount with a 2 inch ball # C45552 for your particular application.

I have also included a link to our help article that explains measuring for rise or drop when choosing a ball mount.

expert reply by: Michael H

0

Answer 1

The Curt T-Connector #C56313 is designed to work on the Premier Trim of the 2019 Chevrolet Malibu. For your Malibu LT I recommend the Curt T-Connector #C56387. This one is confirmed to fit your vehicle and work with the options that are included.

view full answer...

Answer 2

Yes, we do! To add a hitch to your 2024 Honda HR-V, I recommend the Curt item #C68DR. This class I hitch is custom fit and bolts to your Honda with included hardware. This hitch has a 1-1/4" receiver that has a 2,000 lbs towing capacity and…

view full answer...

Answer 3

Thanks for reaching out, John! The Curt Class II Euro Style Drawbar #C45552 has a 2" hitch ball. The hitch ball is fixed and can't be removed so if you want this style and you need to be able to use both a 1-7/8" and…

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

Curt has a nice picture of trailer hitch #C11196 installed on a Cadillac CTS coupe. I have include it for you here. The hitch receiver and cross tube are visible beneath the rear fascia of the vehicle. If you plan on doing any towing with the hitch…

view full answer...

Answer 6

We have just what you need! The replacement motor for your A-300 series Klauber slide out is the part #LC157511. The last 4 digits of the number you listed confirms that you have an A-300 series which is how I know this is the correct replacement.

view full answer...

Answer 7

This will depend on the hitch used and the height of the trailer coupler. You want the trailer to be as level as possible. We have a page on calculating hitch height and coupler height to help you find what ball mount would work best. Most light duty…

view full answer...

Answer 8

The trailer hitches with the highest capacity for your 2019 Infiniti Q50 is the Draw-Tite Trailer Hitch Receiver #24931 and the Curt #C11407. These are both class I which has a 2,000 lb towing capacity and 200 lb tongue weight capacity. I should note…

view full answer...

Answer 9

To safely execute a 90 degree turn you want at least 4 inches of clearance between the truck cab and trailer. The head of the #BWRVK3400-5W is adjustable from front to back so you may be able to adjust it back a little bit for better clearance while…

view full answer...

Choosing the Right Curt Class II Euro Style Ball Mount to Tow a Trailer Level

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching