Replacement Spindles for Featherlite Horse Trailer

Question

Question:

Do you have replacement spindles for a Featherlite Horse Trailer? Can you use the VIN to find the a replacement or do I have to make a visual check after I get the old one off? thanks

asked by: Bill G

0

Expert Reply:

We do offer replacement trailer spindles, and all are shown on the linked page. These include agricultural, EZ Lube and standard types.

Your trailer VIN will not tell us which spindles you need but you can select the right one based on your axle's weight rating and measurements of the current spindle. You'll need a digital caliper like to measure precisely.

Note that new spindles should be welded on only by a professional welder who has experience and the correct jigs for installing spindles perfectly straight and concentric. If not installed correctly the trailer may not track properly and uneven tire wear can occur.

expert reply by: Adam R

0

Answer 1

If the spindles were overheated due to a bearing malfunction then you will need to replace them or the axle. The spindles are already heat treated for strength but you will lose that strength if heated beyond a certain point after the fact. If there…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Replacement Spindles for Featherlite Horse Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching