Replacement Jack Recommendation to Replace Shelby 5784

Question

Question:

Hello.I have a Shelby model 5784 trailer jack with a 1200lb capacity. I was wondering if any of the gear replacement packages you have might fit that model?

asked by: John W

0

Expert Reply:

I have an easier replacement solution that we can provide, but we do not have gear kits for your Shelby jack.

We did have a customer come back and say that the Fulton jack part # FTJ120W0301 will attach just fine to the pipe mount on the trailer frame.

expert reply by: Jameson C

0

Answer 1

As long as your current bracket measures 2-1/8" from the center of the bolt to one of the pin holes then the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 will work great as a replacement for your Shelby 5784 bolt-thru jack.

view full answer...

Answer 2

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784.

view full answer...

Answer 3

The Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will work in place of your 1,000 lb Atwood snap-on jack as long as the bracket that is on the jack matches up with the dimensions in the attached picture. If they don't match up then let…

view full answer...

Answer 4

Since a 5-1/2 inch tall frame is not all that common I recommend using Fulton jack #FTJ120W0301 which comes with its own bracket that will need to be welded to the trailer frame.

view full answer...

Answer 5

According to our research the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on. You basically need to open…

view full answer...

Answer 6

The Shelby #5776 is the direct replacement for the #5756, but we do not offer that particular jack. The Fulton #FTJ120W0301 that you referenced would make an acceptable replacement. The capacity and the amount of lift or travel is identical. Both…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Replacement Jack Recommendation to Replace Shelby 5784

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching