Will Dexter E-Z Flex Suspension System Fit Keystone Bullet Trailer with Wide Stance Axle Placement

Question

Question:

Will this system work on a Keystone Bullet travel trailer with the wide stance axle placement

asked by: JoeD

0

Expert Reply:

I do not have the exact axle measurements for your Keystone Bullet travel trailer, but the E-Z Flex Heavy Duty Rubber Suspension System # K71-653-00 is designed to fit trailers with 35 inches of axle spacing from the center of one axle to the center of the other. The best way to find a replacement equalizer is to match the length and height dimensions (center bolt hole to center bolt hole) of the existing equalizer.

I'm attaching a review video of this suspension system as well as an installation video of a similar system.

expert reply by: Amber S

0

Answer 1

I couldn't find any info on the Dexter equalizer part number you mentioned but if the dimensions of the part #K71-653-00 that you referenced match what you have on your trailer this would work well. I attached a picture that has the dimensions of…

view full answer...

Answer 2

The Road Armor Shock Absorbing Equalizer Kit - Tandem Axle - Qty 2 #LC696740 measure 6 inches center on center. They can work for your 7 inch equalizer replacement, but you may need to replace shackle straps to make up any differences depending on…

view full answer...

Answer 3

Your Ventline CC315-1 range hood should use a 921 bulb like the Replacement #921 Lamp Bulb for Ventline RV Range Hood #VA0415-00. So, for an LED bulb, you can use the: -921/906 LED Light Bulb #DI64ZR. These bulbs have an output of 230 Lumens, and put…

view full answer...

Answer 4

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 5

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 6

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 9

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 10

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 11

I understand your worry Tom, and I have a couple recommendations. First is the MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR which has a height of 4-1/2" for the mounting bolts. This is also 6-1/2" in width like the shorter…

view full answer...

Answer 12

Hey Mike, To determine if the MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR would be a compatible fit you'll first want to measure the bolt hole spacing on your current equalizers. The #MR87ZR has a 6-1/2" center to center…

view full answer...

Will Dexter E-Z Flex Suspension System Fit Keystone Bullet Trailer with Wide Stance Axle Placement

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching