Will Hose part # W01-4180 Work with # SS01 as an Extension Hose

Question

Question:

Will W01-4180 work and connect ok directly to SS01 ?

asked by: Rich

0

Expert Reply:

The SewerSolution Macerator System # SS01 does come with a fitting that will allow an extension hose to be connected. For that the part # W01-4180 would work well.

expert reply by: Jameson C

0

Answer 1

I reached out to my contact at Valterra regarding the SewerSolution Macerator System #SS01 that you referenced and she does not recommend it for your particular application. It simply isn't going to provide enough pressure for the 125 foot…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 5

I looked up pictures of the taillights that are on the 3110 Featherlite trailers and for the LED version of them you would want the part #STL36RB and #STL37RB. It looks like the spare tire mounts for your trailer are something you would have to get…

view full answer...

Answer 6

There are indeed many different replacement step controllers out there and I am happy to re-confirm that the correct current item to replace your Kwikee step controller 1800709 is part #LC363989. I verified this item with my parts contacts at…

view full answer...

Answer 7

Yes. The Hydraulic Trailer Brake Kit - Uni-Servo - Dacromet - 10" - Left/Right Hand Assemblies - 3.5K #AKUBRK-35-D are compatible with the Dexter Trailer Hub and Drum for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Galvanized #8-247-50.…

view full answer...

Answer 8

The thread size is 3/8"-24 but the fitting size is 3/16". This standard for trailer brake lines. This will go from 1/2 inch thread size to 3/8 inch. If the dimensions you took are 1/2 inch and 3/8 inch of the threads this will fit.

view full answer...

Answer 9

If your vehicle's plug was factory installed, I would start by checking to see if you have a blown tow package tail light fuse. I've attached an image from your owners manual highlighting the position 3 location to check the 15 AMP fuse for…

view full answer...

Answer 10

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 11

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Will Hose part # W01-4180 Work with # SS01 as an Extension Hose

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching