Recommended Winch Post/Stand For Boat Trailer With Roller Stop

Question

Question:

I need a winch post complete kit, except for the winch, ready to assemble and mount on my 3X 3inch tongue. I have the winch. The winch needs to be mounted 25inch above the tongue, the roller stop could be above or below the winch.

asked by: Fred K

0

Expert Reply:

It sounds like you are looking for the CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide # CE31013G. This is designed for a 2 inch by 3 inch frame, so you will need to make some modifications. This is the only winch stand we currently carry.

You may also be interested in the Dutton-Lainson Angle Mounting Plate for StrongArm Electric Winches # DL24059 and the CE Smith Keel Roller Assembly for 2" Wide Trailer Tongues - Galvanized Steel and Yellow TPR # CE32015G.

expert reply by: Jason S

0

Answer 1

The CE Smith Winch Stand #CE31013G is basically the complete thing in and of itself. You just need to pick up appropriate hardware to install it to your trailer tongue and then install the actual winch on it and you'll be good to go. The mounting…

view full answer...

Answer 2

The Dutton-Lainson StrongArm Electric Winch, #DL25200, itself is not trailer-specific, so you could use it with any trailer provided that it is mounted properly. We have several mounting kits available depending on where you would need to mount the…

view full answer...

Answer 3

There could be two possible reasons as to why the clutch is not engaging when you are pulling in your boat with the Dutton-Lainson TW4000 StrongArm Electric Winch part #DL25200. The first reason is the simplest to fix and it entails tightening the…

view full answer...

Answer 4

To mount the CE Smith Winch Stand #CE31013G on a trailer requires you to slip the lower portion with the holes drilled through it over the pole tongue of your trailer. The various holes are there to allow you to match the correct height and angle…

view full answer...

Answer 5

The diameter of the mounting bolt hole on the CE Smith Bow Roller Bracket for Winch Stands, #CE31005PG, is .45 inch. The bracket uses a 5-1/4 inches long x 1/2 inch diameter steel shaft for attaching the roller/Y-stop, which is part #CE10700A. The…

view full answer...

Answer 6

The mounting holes on the bottom of the CE Smith Galvanized Winch Stand #CE31013G measure 7/16-inch. Please refer to the linked photo. This 30-inch tall winch stand is made of 12-gauge steel and is intended for 2-inch trailer tongues. It is…

view full answer...

Answer 7

In order to attach the CE Smith Winch Stand part #CE31013G to your boat trailer you would need to cut off the bottom portion of the stand and weld that directly to your trailer's tongue as it is only designed to bolt onto a 2" wide trailer…

view full answer...

Answer 8

I spoke to my contact at Dutton Lainson and they informed me that the Dutton Lainson Adapter plate part #DL24059 that you referenced is 7.7 inches long and 5.50 inches wide.

view full answer...

Answer 9

As the Dutton-Lainson Hand Winch #DL17042 is typically mounted to a horizontal post or beam on a trailer, we will not have a bracket to mount it vertically. That being said, you may be able to adapt the Dutton-Lainson Mounting bracket #DL24059 to…

view full answer...

Answer 10

I have some great electric boat trailer winch options for you such as the Dutton-Lainson StrongArm Electric Winch which is what I recommend. These will need to be rated for about half the weight of the boat, so part #DL25215 for example (full…

view full answer...

Answer 11

I am not familiar with the Trax Electric Winches so I am not sure what their mounting plates look like. However, the Dutton-Lainson winch mounting plate #DL24059 has the top 2 holes spaced 2-1/2" apart. Then the third hole in the middle is down…

view full answer...

Answer 12

The only winch post option we offer is the CE Smith Winch Stand part #CE31013G which is designed for 2" trailer tongues. This will then allow you to mount a winch like the Fulton Single Speed Trailer Winch part #F142102 which is what I…

view full answer...

Recommended Winch Post/Stand For Boat Trailer With Roller Stop

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching