How to Install the SportRack Pop-Up Camper Roof Rack # SR1020

Question

Question:

Bought a sportRack for my tent trailer. You are supposed to drill through the metal trim on the top of it around the edge. Do you know what is beneath it which I will be drilling into?

asked by: TB

0

Expert Reply:

The SportRack Pop-Up Camper Roof Rack # SR1020 installs on the roof of your pop-up camper by first picking out the desired location of the roof rack. You will then take a 1/8-inch drill bit and drill holes through the roof that line up with the holes on the feet of the roof rack. Using the included hardware you will then bolt the crossbars onto your roof to secure the roof rack.

Since you will be choosing where the roof rack installs, whatever is on the inside portion of the roof of your camper will vary.

Please keep in mind that this roof rack will not fit trailer roofs that have rounded or curved edges.

expert reply by: Jon G

0

Answer 1

If the roof of your pop up has a track/channel on top of it for mounting roof accessories the SportRack Pop-Up Camper Roof Rack #SR1020 that you referenced would not require drilling as the channel nuts would slide into the track and you'd…

view full answer...

Answer 2

No it is not, to install this SportRack Pop-Up Camper Roof Rack #SR1020 you need to drill 1/8 inch holes through the exterior of your camper, and then use the self tapping screws to hole the rack to the camper.

view full answer...

Answer 3

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, the Roamer LT Roof Rack for Pop-Up Campers and Camper Shells #S80510 will fit your 2023 Forest River Flagstaff 176LTD. It is also what I recommend to add a roof rack for a bicycle carrier on your camper. Once installed you will be able to add…

view full answer...

Answer 8

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

Pace Edwards has two confirmed fitting Switchblade covers for your 2024 Chevy Silverado 3500 DRW 8' bed; part #PE87CV, which is an aluminum and vinyl mix and part #PE77CV, which is just aluminum.

view full answer...

Answer 11

Yes, that note is accurate. A Class I trailer hitch receiver is limited to only 2 bikes regardless of the amount of weight it's carrying. This is due to the exaggerated force caused by the additional leverage from the bikes being further away…

view full answer...

How to Install the SportRack Pop-Up Camper Roof Rack # SR1020

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching