Dimensions Of The Trailer Tipper Latch by Dutton-Lainson Item # DL13353

Question

Question:

Could you give me the dimensions of this part. I already have the Uinch frame piece the latch goes through welded to my trailer. I need to know is the rest will fit. Thank you.

asked by: John H

0

Expert Reply:

I went out to our warehouse and measured the Trailer Tipper Latch by Dutton-Lainson part # DL13353 for you. The dimension of the latch portion of the component is as follows:

The top part of the latch is 4" long and 1/2" wide. The metal slide attached to the latch is 1/4" thick and has a length of 1-1/2" long x 3/4" wide.

I have attached two pictures that will further depict these measurements.

expert reply by: Conner L

0

click to enlarge

Answer 1

I may have an option for you, but we do not the style catch you have based on the picture you provided. You may be able to use the Trailer Tipper Latch by Dutton-Lainson #DL13353 to replace your current tilting system, and this is currently the only…

view full answer...

Answer 2

It's not the greatest quality picture, but I did attach a picture that shows how a tipper latch like the part #DL13353 will install on a tilt trailer.

view full answer...

Answer 3

I went out to the warehouse and pulled a Trailer Tipper Latch #DL13353. The bolt holes on the bottom take a 3/8 inch diameter bolt. For locking you will actually need to use a locking pin or pad lock with a 5/16 inch diameter. When in the locked…

view full answer...

Answer 4

Running a direct ground up to the trailer tongue or junction box would certainly work, but the only time I'd see that as being necessary is if the lamps were connected to a non metallic structure or a metallic structure that wasn't directly…

view full answer...

Answer 5

Channel Tongue Trailer Coupler #CT-3001-Z requires a 2 inch wide tongue but I recommend a boxed tongue and not C-channel so there is more support where it counts. Steel tubing at least 1/8 of an inch of wall thickness will do the trick. The length…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Dimensions Of The Trailer Tipper Latch by Dutton-Lainson Item # DL13353

Product Page this Question was Asked From

Continue Researching