Installation of Brake Controller on a 1999 GMC Yukon

Question

Question:

can not find the plug port under the dash anywhere, on my 99 yukon.

asked by: MICHELLE W

0

Expert Reply:

The 1999 GMC Yukon will not have a brake controller plug-in port under the dash. To install a brake controller on your vehicle you will need to hardwire the brake controller with the Brake Controller 7 and 4 Way Installation Kit, part # ETBC7.

To install the # ETBC7 kit you will need to have a 4-Way connector at the rear of your vehicle. If you need to install a 4-Way connector you can use the Tow Ready T-One Wiring Harness, part # C55319. The Tow Ready harness will plug into a connection point located along the inside of the drivers side frame rail. This will give you a 4-Way connector at the rear of your vehicle. I am including a link to the instructions on the Tow Ready wiring harness.

With the 4-Way connector at the rear, you can then add the # ETBC7 kit. The 4-Way plugs into the back of this harness leaving only 4 wires to hardwire. I am including a link to two FAQ articles and a video that will explain how to install an ETBC7 kit.

expert reply by: Jeff D

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 5

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 6

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 7

There are a number of factors involved when converting a semi 7-way to an RV 7-way. Semis generally use a 7-pin round pin socket, similar to #PK11720. And RV style 7-way uses blades, like #PK12706. We do not offer any pre-made adapters to make this…

view full answer...

Answer 8

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Installation of Brake Controller on a 1999 GMC Yukon

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching