Will the Reese Titan WD Shank # RP54976 Work with Reese Weight Distribution # RP66074
Question:
I have a 2011 Ford Super Duty and it came equipped with a 2 1/2 inch receiver. I am planning on purchasing the Reese dual-cam set up in the future. My question is...Will the Reese hitch head from kit #RP66074 fit on the Reese 2 1/2 inch shank #RP54977? I would like to use this combination so that I dont have to use an adapter when towing my travel trailer. Thank you in advance for your help.
asked by: Dave M
Expert Reply:
The Reese Titan Weight Distribution Shank, part # RP54977, will fit the Reese hitch head in the Reese weight distribution kit, part # RP66074. You will want to make sure that the 5-3/4 inch drop or 8-1/4 inch rise on the Reese Titan # RP54976 shank will work properly for the setup on your 2011 Ford Super Duty.
To make an approximate determination of the rise or drop that is needed for your weight distribution shank, first jack up your trailer so that it is level and measure from the bottom of the coupler to the ground. Add an inch or two to this measurement to account for sag when the trailer is hitched. Next, measure from the top of the hitch receiver on the vehicle to the ground. The difference between these two measurements will be the rise or drop needed on the weight distribution shank for your vehicle.
I am including a link to a FAQ page on weight distribution and a FAQ page on measuring for rise and drop.
Products Referenced in This Question
Strait-Line Weight Distribution w/ Sway Control - No Shank - Trunnion Bar - 12K GTW, 1,200 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Shank Not Included
- Electric Brake Compatible
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- Allows Backing Up
- 1000 lbs
- 1100 lbs
- 700 lbs
- 800 lbs
- 900 lbs
- Reese
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: hitch
- Shop: Gooseneck Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2"
- Search Results: 16055
- Search Results: hitch receiver
- Search Results: 15845
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: 56332
- Search Results: 54976
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: bike racks
- Shop: Curt Welded Weight Distribution Shank 7" - 10 Hole Adjustment
- Shop: Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 10" Rise/6" Drop
- Shop: Adjustable Ball Mount for 2" Hitches - 9" Rise to 10-1/4" Drop - 5,000 lbs
- Q&A: Availability of 2-1/2 Inch Shank for Reese Weight Distribution System
- Q&A: Troubleshooting Non-Functioning 12V Trailer Power Feed on 2016 Silverado 2500
- Q&A: Should Hitch Ball Angle Be Adjusted Up and Down or Angled to the Rear Using Weight Distribution
- Article: 5 Things to Know About Weight Distribution Hitches
- Video: Choosing the Right Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose the Right Trailer Hitch Class
- Video: Choosing the Right Brake Controller
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Shop: Brake Controller
- Article: Trailer Wiring Diagrams