Does Lippert Ground Control System have to be Recalibrated if Battery Power was Removed

Question

Question:

Does Ground control unit need to be re calibrated after disconnecting the battery?

asked by: David

0

Expert Reply:

If the battery power was only briefly disconnected from the Lippert Ground Control system # LC358590 (a few seconds) then it will likely not erase any memory and you would not have to recalibrate the system. But if the battery power was lost for an extended period then you would likely have to go ahead and run through the initial set up process to ensure everything is working properly. I have linked the instructions (aftermarket version) for reference.

expert reply by: Michael H

0

Answer 1

I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast and the system won't reset. He…

view full answer...

Answer 2

Often an issue like you stated has to do with the battery not being fully charged. If the battery is even slightly low, sometimes this system is a little finicky. I recommend first charging your battery fully and testing it to ensure it is fully…

view full answer...

Answer 3

The Replacement Auto Level Control Panel for Lippert Ground Control Leveling System part #LC421484 is just a newer version than the one you have now and can be used as a direct replacement. I was able to confirm this with my contact at Lippert.

view full answer...

Answer 4

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set #LC675817 does require adequate power to work properly. I recommend checking your ground connection from your battery to the trailer frame and…

view full answer...

Answer 5

The Replacement Trivet Support Bumper for Furrion Chef Collection Gas Cooktop #CFGH4ZSASSTRIVETSPRT are solid in a quantity of one. So if you need multiples, you would order the exact number that you needed. These are a direct replacement for the…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Does Lippert Ground Control System have to be Recalibrated if Battery Power was Removed

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching