How to Pick Out Replacement Hub for Trailer
Question:
I have a 2005 Performance Single axle trailer.....looking to replace the hubs ...which product do I need. Holds a Pioneer 197 CC so I assume it is a 3500# axle?
asked by: Jay T
Expert Reply:
In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your wheels. I attached an FAQ article on determining bolt pattern for you to check out.
Next thing you will need to know is what spindle you have on your trailer. In order to do that you can either get the inner and outer bearing numbers from a hub or use a dial or digital caliper to get exact measurements of the spindle. The measurements needed are the parts of the spindle where the bearings ride.
If you get back to me with that information I will help you pick out the right hub assemblies. Or, you can follow the link I attached that will take you to the page that has all of our replacement hubs.
You would want to first select the bolt pattern that you have, next select the inner bearing you have, followed by selecting your outer bearing, and then all the correct hubs will be listed.
Product Page this Question was Asked From
Dexter Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 3500 lbs
- Brake Assembly
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Dexter Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Video: Dexter Electric Trailer Brake Kit Installation 23-26
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb Axles - 12" Diameter - 6 on 5-1/2
- Shop: Electric Trailer Brake Assembly - Self-Adjusting - 10" - Right Hand - 3,500 lbs
- Shop: Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Shop: Dexter Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 6 on 5-1/2 - Pre Greased
- Q&A: Amperage of Brake Magnets and Size of Wire Used To Connect 7-Way Trailer Plug To Electric Brakes
- Q&A: How to Tell Left and Right Side of a New Dexter Axle without Taking Off the Hubs or Brakes
- Q&A: Replacement Brake Magnets for 10 Inch Brakes on 3500 Pound Trailer Axles
- Q&A: Can Electric Brakes be Used on a Boat Trailer
- Shop: Trailer Hitch
- Search Results: 25580
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Most Popular Wheel Bearings
- Shop: Trailer Wiring
- Video: etrailer Electric Trailer Brake Kit Installation
- Search Results: l44649
- Article: Trailer Wiring Diagrams
- Q&A: How to Measure to Determine the Size Trailer Brakes Needed For Hydraulic Drum Replacement
- Article: Trailer Tire Sizing
- Q&A: How to Determine the Size of a Trailer Hub Assembly for Replacement
- Search Results: fender
- Shop: Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 10~36
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Shop: Suspension Enhancement
- Video: Choosing the Right Brake Controller