Surface Mount Trailer Clearance Light Availability

Question

Question:

Ive already asked a similar question and now need a follow up. I want to mount the lights STL101RB on my trailer using the flange A45SB. Because of the peculiarities of my situation a lot of these are because this is a 66 Apache popup I need the light to extend out and not be recessed. Will these lights mount into the flange backwards? Thanks again for all the help!

asked by: John V

0

Expert Reply:

For what you are looking for a surface mount light like the part # STL43RBX would probably be a better option as it doesn't require a bracket and it does stick out a little bit.

expert reply by: Jameson C

0

Answer 1

The Optronics Tail Light #STL43RBX does not need a bracket for mounting. It has a built in flange and includes a rubber grommet. The light can be connected using a 3-wire pigtail, #A45PB, or #A47PB for a right angle.

view full answer...

Answer 2

Thank you so much for your photos. We don't have an exact replacement light for you, but we have something very close. It's the Optronics LED Trailer Tail Light, part #STL13RFHXB. This LED light measures 5-5/8" in diameter…

view full answer...

Answer 3

They are single function lights, so they can be used as running lights or stop/turn but not both. So for your trailer to be legal, you will need to run two on each side, one for the running light (brown wire of your 4-way) and one for the turn/stop…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Surface Mount Trailer Clearance Light Availability

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching