Recommended Wheel Center Cap For Truck

Question

Question:

Greetings, I just bought a truck that has after market chrome wheels. There is no brand name on them, but the center hub covers are missing. They need snap-in style, push-through will not work. The bore is 4.25 inch or about 108 mm. Do you have ANY style of snap-in center caps in that size? I would prefer chrome but will consider all possibilities. Thanks!

asked by: Paul

0

Expert Reply:

For the 4.25 inch pilot hole, we have the Trailer Wheel Center Cap, Chrome, 4.25" Pilot Size # 425EZ. This is the closest option we have for your chrome caps of that size. We don't have just plugs in that size.

expert reply by: Jason S

0

Answer 1

Snap-In Plug for Lionshead Trailer Wheel Center Caps #LHSI60C measures 2.17 inches in overall diameter and from the outside of one tab to the outside of the opposite tab is 1.92 inches. I have included a picture showing this. This cap was designed…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 6

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 7

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 8

Hi Tom, I have two options to replace the electric tongue jack on your Jayco Whitehawk: Option 1: Electric Jack w/ Footplate #EJ-3520-BBX. This jack is going to be your no-frills 'get the job done' style jack. It has a 3,500lb capacity and…

view full answer...

Answer 9

Pete, yes the Snap-In Plug for Lionshead Trailer Wheel Center Cap #LHSI60C are definitely not brittle and are better made than most. This is still made of plastic, has a chrome finish, and will work with 15" to 16" diameter wheels with a 6…

view full answer...

Answer 10

You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub you…

view full answer...

Answer 11

What you have is an 86" long axle with a 4,400 lb capacity. Since 4,400 lb axles are no longer being produced, you will need an axle with a higher capacity for a replacement. I recommend the Trailer Axle Beam with Easy Grease Spindles #e45GR.…

view full answer...