How to Pick Out Bearings for Komfort 5th Wheel Trailer

Question

Question:

1984 Komfort 5th wheel trailer, T class. I need trailer bearings, cotter pins, races and seals. Do you carry them and how much are they. Thanks.

asked by: Danny

0

Expert Reply:

To pick out bearings for a trailer hub you will need to remove one of the hubs so that you can remove the bearings and get the numbers off of them.

Or, you can measure the spindle where the bearings ride so that we can pick you out the correct bearings that would fit the spindle.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 4

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 5

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 6

Hey Dave, what you gave me is enough info to get you replacement bearings. The grease seal 471750 matches the part #TMK48ZR. For a Timken replacement for the L44610 part number you'd need #TMK63VR. Then for a bearing for the L44649 you'd want…

view full answer...

Answer 7

The only difference between the #RG06-050 and Timken #TMK58ZR is the brand and quantity. Timken is typically considered to be a high quality brand, particularly for their USA made bearings. The #RG06-050 comes with two seals so it is the better…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

How to Pick Out Bearings for Komfort 5th Wheel Trailer

Product Page this Question was Asked From

Continue Researching