Anti-Rattle Device Recommendation for Class III Ball Mount to Remove Movement in Hitch

Question

Question:

Hi, I recently purchased a class three hitch, mount, pin and wiring harness from e trailer. it works great, installation was easy, but the mount bangs severely while driving, especially with an empty trailer. I am new to towing. Any suggestion on quieting it down, Thanks

asked by: Gregory B

0

Expert Reply:

What you need is an anti-rattle device to prevent the ball mount from moving in the hitch you have installed.

The part # 63232 is the best option for that as it will remove the movement and it doubles as a hitch lock.

expert reply by: Jameson C

0

Answer 1

There is not a cover available, but if you are looking to protect your cargo from the elements we do have weatherproof cargo bags available. The Extra Large Cargo Carrier Bag, part #988501offers 20 cubic feet of storage space, and is our best seller.…

view full answer...

Answer 2

The sleeve of the #SHP2040-XL lock isn't meant so fit all the way through the receiver, if it did, it wouldn't allow the threaded square nut to tighten against the inside of the ball mount or hitch accessory. The up and down movement should…

view full answer...

Answer 3

The anti-rattle hitch lock you referenced, part #SHP2040-XL does not carry a weight rating, but it is only compatible with ball mounts that have hollow shanks. Ball mounts with hollow shanks usually have a maximum capacity of 7500 lbs, so 7500 lbs…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

I drew up a diagram below that displays the dimensions from the center of the mounting points to the center of the crosstube so that you can measure and determine if the Curt Custom Base Plate Kit #C68FR would clear the bumper. In the attached video…

view full answer...

Answer 9

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Answer 10

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

The Large Yakima OffGrid #Y07139 Cargo Basket uses crossbar clamps that are designed to be universal. They will fit virtually any crossbar shape, including most aftermarket and OEM crossbars. I was not able to find any schematics online that would…

view full answer...