Will Lippert Stabilizer Jack # LC298707 Replace 113407 Jacks

Question

Question:

I have a 2015 jayco eagle ht 32.5bhs fifth wheel and it has a lupper 113407 rear jack. Wondered if the lc298707 will fit. What is the width of this jack?

asked by: Jeff

0

Expert Reply:

The 113407 stabilizer jack you have now is the standard Lippert stabilizer jack. If you wanted to replace it with the part # LC298707 that you referenced you certainly could.

Overall width is 70-15/16 inches and the mounting hole centers are 68-11/16" apart.

expert reply by: Jameson C

0

Nancy W

4/14/2020

we have a 2009, 39ft, freedome elite, mk39 that has the 113407 rear stabilizer on it, we need to replace, is there a difference between the #lc298707 or #lc369774..ie will both of them work?

Reply

Chris R.

4/15/2020

Both the Lippert # LC298707 and # LC369774 will work great on your trailer - the stabilizers themselves are identical between these two part numbers. The only difference between the two is the type of switch that comes with it. The # LC298707 features a black waterproof switch and # LC369774 includes a white switch.

Reply

Nancy

4/16/2020

Thank you, we bought this used and the stabilizer bars etc were there but motor was missing, we replaced the motor, the motor is good however there appears to be something locked up inside the stabilizer assembly and its not turning to let them down, even by hand, can we buy just the stabilizer assembly by itself without having to buy a kit since we already bought the motor separate?

Reply

Chris R.

4/16/2020

Unfortunately just the stabilizer isn't available from Lippert without the included motor. The only way to obtain the stabilizer is to purchase the complete system. I wish I could have given you better news.

Reply

Answer 1

The direct replacement for your Lippert Model 113407 stabilizer jack is part #LC369774. I confirmed this with my contact at Lippert. It requires an easy bolt-on installation.

view full answer...

Answer 2

The Lippert High-Speed Power Stabilizer Jack #LC369774 referenced in your question is indeed the correct replacement for your existing Lippert 113407 system. I verified with my contact at Lippert that the mounting hole spacing is the same between the…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 6

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 7

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 8

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 9

You will need the Ceiling Garnish for Fan-Tastic Vents Roof Vent #FVK1060-81 as it is specific to your Dometic Fantastic Fan 1450. The Ceiling Garnish for Ventline Roof Vent #VA0445-37 is going to have rounded corners as opposed to the square on the…

view full answer...

Answer 10

In regards to HappiJac Truck-Mounted Camper Tie-Downs like part #LC182908-182928, the front tie-down installs inside the bed on the front panel directly behind the cab. The rear tie-down then mounts to the bumper. They will not require removal of the…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.

view full answer...

Will Lippert Stabilizer Jack # LC298707 Replace 113407 Jacks

Product Page this Question was Asked From

Continue Researching