Dimensions of B&W 2-5/16 Inch Hitch Ball # BWHB94009

Question

Question:

What is the height from where the shank starts.

asked by: Fred D

0

Expert Reply:

I went out to our warehouse to take a look at the B&W 2-5/16 Inch Hitch Ball # BWHB94009 referenced in your question. From where the shank starts up to the top of the hitch ball, there is a distance of 3-1/4 inches.

I have included an image with this measurement labeled for you to check out.

expert reply by: Chris R

0

click to enlarge

Answer 1

The most popular trailer wheel bolt pattern is the 5 on 4-1/2 inch bolt pattern and as far as we are aware the bolt pattern you mentioned is not used on trailers at all. So my bet is you probably have the 5 on 4-1/2 inch. I attached a help article…

view full answer...

Answer 2

Lunette rings do come in more than one size. The linked page displays both 2-1/2-inch and 3-inch inner diameter. . Lunette ring accessory items are also shown on the other linked page. Weight capacities for lunette rings are substantial, ranging from…

view full answer...

Answer 3

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 4

The leaf springs we offer for 3,500 lb axles are 4-leaf setups like the part #e54SR which is 25-1/8 inch long. The next capacity we offer higher than this is 4,500 lb which is also a 6-leaf setup with the part number #e27SR. This one happens to be 26…

view full answer...

Answer 5

You should have 3 wires at the rear of your LED light, or from a pigtail like part #A47PB, that plugs into a light like part #STL22RB. The red wire will be connected to your stop/turn circuit on your vehicle. The black wire is spliced into your…

view full answer...

Answer 6

The Dexter Electric Brake Kit w/ Cast Backing - Self-Adjusting - 12-1/4" - Left/Right Hand - 15K #23-446-447 will fit any 15K axle that have the standard 7 bolt mounting flange. These are self-adjusting brakes so there is no need for manual…

view full answer...

Answer 7

If the landing gear on your brand new Forest River Trailer is not working at all, either to extend or retract the legs, then most likely there is some kind of a power issue. I do recommend starting by making sure the battery is charged and in good…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Dimensions of B&W 2-5/16 Inch Hitch Ball # BWHB94009

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching