Replacement Hinges For Extang 56430 Solid Fold Tonneau Cover

Question

Question:

hello I am looking for repair parts for Extang 56430 solid fold tonneau cover. Specifically the hinges would need to be replaced. Can you provide any assistance?

asked by: Jenn

0

Expert Reply:

I reached out to my contact at Extang and there are replacement hinges available for the Extang Solid Fold Tonneau. To help you get the correct replacement hinges, I need to have the lot number on your cover. It will be on a white sticker on the underside near the part number.

expert reply by: Jason S

0

Answer 1

I spoke with my contact at Extang a while back about the install of the front clamp for Trifecta Cover part #EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly…

view full answer...

Answer 2

Thanks for your picture from that it looks like you have an Extang Trifecta tonneau cover and are needing a replacement cab clamp assembly part #EX1034. This is the only way to order and replace the part you are needing to replace.

view full answer...

Answer 3

Yes, the part #EX1035 is the correct replacement tail clamp assembly for an Extang Solid Fold tonneau cover like what you have. I attached install instructions for this clamp for you to check out as well.

view full answer...

Answer 4

I can help you with the process of replacing the Tail Clamp Assembly #EX1035 for your Extang Solid Fold or Solid Fold 2.0 tonneau cover. The replacement process will be different depending on if your existing cover is the Solid Fold or the Solid Fold…

view full answer...

Answer 5

I can help you with the process of replacing the Tail Clamp Assembly #EX1035 for your Extang Solid Fold or Solid Fold 2.0 tonneau cover. The replacement process will be different depending on if your existing cover is the Solid Fold or the Solid Fold…

view full answer...

Answer 6

None of the methods are super easy. I'd recommend three though you have to remove hinges. This is least invasive, doesn't require cutting the cover, and also doesn't risk damaging cover.

view full answer...

Answer 7

You certainly can substitute the #EX1035 tail clamps with the #EX1034 cab side clamps for a more snug connection. Extang tells me that doing so is perfectly acceptable, but it will make removing the cover more difficult.

view full answer...

Answer 8

Yes, the Replacement Cab Clamp Assembly part #EX1034 is a fit for a Extang Trifecta 2.0 Soft Tonneau Cover. In regards to installation, you'll need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab…

view full answer...

Answer 9

Hey Chad, so I'd actually recommend a mid size ladder rack like the Yakima OutPost HD Overland Truck Bed Rack #Y01152-58. This is by far going to be your best bet if you don't want to trailer your kayaks. These bars have a 500 lb weight…

view full answer...

Answer 10

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 11

Hey Gregg, The etrailer Hard Tonneau Cover #e23DR mounts to the inner lip of the bedrails with clamps so you'll need access to that lip in order to install it. If your bed liner is plastic you can just cut out holes where the clamps sit in order…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Replacement Hinges For Extang 56430 Solid Fold Tonneau Cover

Product Page this Question was Asked From

Continue Researching