Correct Bearings for 1-3/8 Inch Spindle

Question

Question:

the bearing part number L68149 1.378 does that work with a 1 3/8ths spindle?

asked by: Daniel

0

Expert Reply:

I do have the correct bearing for a 1.375" spindle like part # TRU59FR however, the L68149 bearing is not the correct bearing for this spindle. The correct bearing for the 1-3/8" spindle is the L44643 bearing like that in the Bearing Kit for 1" BT8 Spindle part # BK1-100 which is designed for 2,000 lb. axles.

The Replacement Trailer Hub Bearing part # L68149 is compatible with an #84 spindle such as the Spindle # TRU24FR which is designed for use on a 3,500 lb axle.

I have attached our wheel bearing help article for your review.

expert reply by: Conner L

0

Answer 1

Yes, that spindle does look too beat up to be usable. I attached a link to this page that has all of the spindles we carry. You would need to pick out the one that matches the axle capacity on your trailer. It looks like maybe a 2,200 or 2,000 lb…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 5

Dexter part 10-41 is a grease seal for a mobile home utility hub. It has a specified inside diameter of 1.938-inches and an outside diameter of 2.523-inches. The nearest match we offer is the Redline part #10-40 which is a single-lip seal that has…

view full answer...

Answer 6

So from what I can gather, the E3 error code on your Furrion Electric RV Fireplace with Logs #F30SW15ABL is an "overheat protection" error which explains why it only runs for a bit before shutting off. I'd recommend…

view full answer...

Answer 7

We have a similar etrailer hitch that fits your 2021 Ram 1500 Classic with the part #e98852, but the #e28ZR fits the non-Classic models.

view full answer...

Answer 8

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328…

view full answer...

Answer 9

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

There is a way for you to find out exactly where to place the center hanger of your 18 foot tandem axle trailer. If you take a look at the diagram I added, which is part of a help article I also linked on how to determine where to put your…

view full answer...

Correct Bearings for 1-3/8 Inch Spindle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching