Are The Sway Bars Of The Equal-i-zer Weight Distribution System Supposed To Be Greased?

Question

Question:

Are the sway bars suppose to be greased?

asked by: Mike

0

Expert Reply:

The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 4,000 lbs GTW, 400 lbs TW # EQ37040ET uses 4 point metal on metal friction to control sway. You definitely DO NOT want to use grease on these trunnion bars. That would cause the system to not operated as intended.

expert reply by: Jason S

0

Answer 1

The only lubricant we recommend for use with the Equal-i-zer weight distributions is the Equal-i-zer High-Performance Lubricant #EQ91-00-4250.

view full answer...

Answer 2

Yes, it is never going to hurt to grease the hitch ball and it would make for disconnecting the coupler easier so I do recommend this. For this, we have the White Grease Hitch Ball Lube part #58117 which works really well. The hitch ball grease in…

view full answer...

Answer 3

Yes we do offer grease for hitches. I recommend White Grease Hitch Ball Lube Item #58117.

view full answer...

Answer 4

I can help you with greasing up your EZ Lube Axle. First thing I would check would be that the grease is not coming out of the back of the axle through the seal. If this is the case you will need to replace the seal. Our tubes like #L11390 have 14…

view full answer...

Answer 5

I have a great solution to carry a bike rack but the dual hitch adapters from Roadmaster are not rated for use when towing trailers. They are only for flat towing vehicles where there won't be trailer tongue weight. Instead we have the Lippert…

view full answer...

Answer 6

With your tongue weight being 680 pounds, which will include the weight of the tanks as long as they came installed from Rockwood, the Fastway e2 Weight Distribution w/ 2-Point Sway Control - Round - 10,000 lbs GTW, 1,000 lbs TW #FA94-00-1000 will…

view full answer...

Answer 7

To convert your Fastway E2 part #FA92-00-0600 to a 1,000 lb tongue weight kit you just need to swap your current spring bars out for the replacement Trunnion bars part #FA92-01-1099 and you'd be set.

view full answer...

Answer 8

The Fastway e2 weight distribution (WD) 8,000 lb and 10,000 lb systems do use the same head units so you can easily use the 1,000 lb Trunnion Bars #FA92-01-1099 or 2 of the Rounds Bar #FA94-02-1099 with your current setup depending on which you have.…

view full answer...

Answer 9

To swap out the 800 lb tongue weight spring bars of your E2 system to 1,000 lb spring bars you would want the part #FA92-01-1099.

view full answer...

Answer 10

The highest-rated round bar Fastway Weight Distribution Hitch is the 10,000 lbs GTW, 1,000 lbs TW #FA94-00-1000. The system has 1,200 lb rated trunnion bars, but because these use a different head unit, this does require a new set up, the Fastway e2…

view full answer...

Answer 11

You will not need to change the bars on your Fastway e2 weight distribution hitch unless you decide to move up to the 1,000lb bars. The propane tank bracket on your Grand Design Imagine 2910 travel trailer is mounted to the top of you frame with…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Are The Sway Bars Of The Equal-i-zer Weight Distribution System Supposed To Be Greased?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching