Installing The Replacement Motor On The Solera Power Awning

Question

Question:

Are there any video on how to install

asked by: Martin C

0

Expert Reply:

The Solera Power Awning Replacement Motor # LC266149 does not have an installation video at this time. However, the installation is not difficult. Before removing the motor, you want to open the awning about 12 inches and support the arms. This will remove the spring tension in the awning roller for an easy removal.

You disassemble the protective housing, remove the bolts that hold the motor in place and then disconnect the 2 wires. To install the new motor, you simply reverse the steps. Plug in the corresponding wires, make sure the gears fit properly, and replace the bolts. Reassemble the protective housing and test the unit. You should be good to go.

expert reply by: Jason S

0

Donna

9/7/2020

Please help, where does the busing and clip go?

Reply

Jon G.

9/10/2020

If you refer to step 12 of the installation instructions on the conversion kit you insert the cotter pin into the end cap to lock the spring head in place. In step 16 you remove the cotter pin once you're done. I'm not quite sure what bushing you are referring to though.

Reply

Answer 1

To remove the retaining clips #17109 on a Curt weight distribution system with round bars you would first remove the bottom screws holding them on. Then you would push the clips up so the wider part of the hole can slip off the top pin. The top pin…

view full answer...

Answer 2

The Draw Tite hitch part #75085 is a fit for your 2003 Chevy S-10 with the sportside non-towing bumper that you have. It would be a great option. For trailer wiring you then would want the part #118359. If you wanted to do some towing you might be…

view full answer...

Answer 3

There are not specific instructions on how to replace the Replacement Rain Shield for MaxxFan Deluxe Roof Vent - Smoke part #MA05-30520 on the MaxxFan Deluxe Roof Vent w/ 12V Fan - Manual Lift - 4 Speed - Smoke part #MA00-06401K. However, replacement…

view full answer...

Answer 4

The Yakima Rack and Roll Trailer, #Y08107 for the 78 inch or #Y08106 for the 66 inch can handle either one 17 foot kayak or two 16 foot kayaks. Extension are available for longer kayaks. Using extension #Y08109 you will be able to carry up to one 22…

view full answer...

Answer 5

There is absolutely a trailer hitch that fits your 2019 Toyota Corolla hatchback, the Curt Trailer Hitch #C11567. This is a Class I hitch with a 1-1/4" receiver so it will work perfectly with your Kuat Beta 2-Bike Rack #B202-114, which is rated…

view full answer...

Answer 6

The BAKFlip G2 Hard Tonneau Cover #BAK26203 you have installed on your 2008 Dodge Ram 2500 sits inside the truck bed rails thus is compatible with stake-pocket-mounted accessories such as the Erickson Retractable Tie-Down Anchors #EM01003. These…

view full answer...

Answer 7

Those do indeed look like locks that are made by Thule. The replacement keys for Thule Lock Cylinders #THLOCKN144 and #THLOCKN053, which it looks like you have are parts #THKEYN144 and #THKEYN053. If you would like to have matching locks so that you…

view full answer...

Answer 8

The Glacier Cable Tire Chain, #PW3010C, is compatible with the P245/65R17 tires that are currently on your 2008 Toyota Highlander, however, they are not compatible with tire sizes P245/60R18 or P245/55R19. The Glacier Cable Tire Chain, #PW2029C, will…

view full answer...

Answer 9

The 1958-1980 Chevrolet oil filters had 13/16 inch-16 thread sizes and used a gasket that have a diameter of 3-1/2 inches. The Derale Tube-Fin Engine Oil Cooler Kit #D15505 that you referenced would be the correct choice for you since it has…

view full answer...

Answer 10

I just got off the phone with a Rad Power Bike specialist to learn more about your situation and found a solution to your problem. The RadRover 5 weighs 69.9lbs with the battery installed. I along with Rad Power Bikes recommend that you do not haul…

view full answer...

Answer 11

the only exclusions for the trailer hitches that fit the 2016 BMW X5, #75600 and #13077, is that they will not fit M models. For trailer wiring I recommend ZCI harness #119250KIT because with it you will not have to cut and splice into the vehicle…

view full answer...

Answer 12

Currently we do not have a rack system designed to attached to round tubing on a utility trailer. Round tubing naturally is a challenge for this application since it could allow any mounting hardware used (say u-bolts, for example) to rotate. If you…

view full answer...

Installing The Replacement Motor On The Solera Power Awning

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching