What is the Size of the Opening on the Replacement Socket for a Equal-I-zer WD System

Question

Question:

Can you tell me the size of the opening? Is it 1 3/8?

asked by: Bob

0

Expert Reply:

The opening on the Replacement Sockets for Equal-I-zer Weight Distribution System, # EQ90-03-1000, measure just over 1-3/8 inches.

The actual measurement of the opening is 1.380 inches which is very close to 1-3/8 inches.

expert reply by: Jared P

0

Answer 1

I reached out to a representative of Equal-i-zer, who told me that the sockets from the 1,200 lb tongue weight head #EQ90-02-1200 will not fit in a 1,000 lb tongue weight head #EQ90-02-1000 because they are too big. If you need additional sockets for…

view full answer...

Answer 2

I spoke with my representative at Equal-i-zer and the grooves that you see at the top and bottom of the spring bar receiver on the head is normal wear. He also mentioned that keeping the receiver lubricated will help reduce on wear in the future, but…

view full answer...

Answer 3

The Equal-i-zer weight distribution spring bars and heads are both designed to fit specific tongue weight ratings so you'd have to replace both. So to uprate your system to 1,000 lbs tongue weight you'd need the head part #EQ90-02-1000 and…

view full answer...

Answer 4

The Replacement Socket for Equal-i-zer 1,000 Lb Weight Distribution Systems part #EQ90-03-1000 is larger than the Replacement Socket for Equal-i-zer 600 Lb Weight Distribution Systems part #EQ90-03-0600 therefore, it cannot be used with the…

view full answer...

Answer 5

The Replacement Spring Bars #EQ90-01-1099 are the correct replacement bars for your 1,000 pound Equal-i-zer weight distribution system. This will include 2 spring bars. The part #EQ90-02-1099 referenced in your question is the same product, however…

view full answer...

Answer 6

We do carry the Pins and Thumb Clips #EQ95-01-9415 to hold the spring bars in place if you prefer them over the Socket Pin #90-03-9212 and Clip #90-04-9216. I personally have never dealt with any issues of these pins and clips falling out. Since…

view full answer...

Answer 7

Yes, the Equalizer Head part #EQ90-02-1000 that you referenced is the correct replacement head for the 1,000 lb tongue weight system part #EQ37100ET that you have.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

What is the Size of the Opening on the Replacement Socket for a Equal-I-zer WD System

Product Page this Question was Asked From

Continue Researching