Diameter Of Grease Cap Included With # 8-173-16UC3 Hub And Drum Assembly

Question

Question:

What is the size of the grease cap of the Dexter brake drum Item # 8-173-16UC3?

asked by: Ken G

1

Helpful Expert Reply:

I went to the warehouse and measured the grease cap that is included in the Dexter Hub and Drum Assembly # 8-173-16UC3.

The diameter of the grease cap that is inserted in the hub measures 1.98 inches.

expert reply by: Jeffrey L

1

Answer 1

I went out to the warehouse and pulled hub and drum assembly #8-173-16UC3 to measure it for you. From the surface where the wheel would sit to the end of the base of the drum is approximately 3-7/8 inches.

view full answer...

Answer 2

The only way to know for sure is to check your bearings. That being said, the most common 4-bolt configuration is a 4 on 4 bolt pattern, which are typically found on 2,000 lb to 2,700 lb trailer axles. The only 4 on 4 bolt pattern hub and drum…

view full answer...

Answer 3

For your Fishing Holdings Trailer, I recommend the Dexter Hydraulic Trailer Brake Kit - Uni-Servo - 7" - Left and Right Hand Assemblies - 2.5K #23-398-399. These can be used with the Dexter 4 on 4 Complete Hub-and-Drum Assembly - for…

view full answer...

Answer 4

When trying to find the correct drum brakes, a measurement of the inside drum diameter and the depth of the drum will be needed. See attached picture. The drum that you referenced, #8-173-16UC3, measures 7 inches in diameter and 1-3/4 inches deep.…

view full answer...

Answer 5

I have attached a great article at the bottom of this page that details all the components needed to install electric brakes on a trailer. The particular parts you need will depend on the camper's axle capacity along with the inner and…

view full answer...

Answer 6

We do offer just the 7-inch hub and drum without bearings, seals, and races for hydraulic brakes but we do not sell the hub and drum for electric brakes without those components. The hub and drum assembly I recommend is part #8-173-16UC3. This does…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Diameter Of Grease Cap Included With # 8-173-16UC3 Hub And Drum Assembly

Product Page this Question was Asked From

Continue Researching