Replacement 3 inch Waste Valve to Replace Bristol Waste Valve

Question

Question:

the 3 inch waste valve on my 2013 5th wheel leaks a little. it is a Bristol valve. will the valtera products work to replace the valve?

asked by: Mike S

0

Expert Reply:

Yes, the Valterra RV 3 inch Waste Valves, like part # T50, are designed to fit standard waste fittings. The part that I referenced is just the regular waste valve. If you are looking at a specific design, you can find a variety of designs on the linked product search page.

You will want to make sure to use Solvent Cement, like part # A05-0303, for a complete and secure installation.

expert reply by: Jon G

0

Margaret C.

7/29/2020

My Bristol 3 inch waste valve will not open when I pull the handle out. How do I drain the waste tank so that it can be repaired?

Reply

Jon G.

8/7/2020

Are you able to see if the waste valve actually moves? It could be that the cable connection is a little loose and just tightening it up will get the valve to move. Worst case scenario would be having to open up your sewage with it still full.

Reply

Margaret C.

8/7/2020

@JonG the handle pulls out of the valve ‘box’ but the ‘door’ inside is not connected. Where is the cable connection?

Reply

Jon G.

8/17/2020

@MargaretC Some waste valves have the handle located elsewhere so there is a cable that is used to open and close the "door", like part # 34466N4BB72GM. If yours just has the handle then this could get a little messy, not going to lie. I saw a few people tried using a 2x2 and lightly tapped on the "door" part of the valve to try and break any seal that might have formed, and then they used needle nose pliers to open the door from where the handle would normally attach to the door.

Reply

Answer 1

It sounds like you're looking a for a new valve assembly for your black water tank. For a black water waste valve for a standard 3-inch diameter twist-on bayonet/lug fitting you can use Valterra part #T58. If your RV instead has a straight sewer…

view full answer...

Answer 2

No they will all mount differently. For example, LaSalle Bristol Cable-Actuated RV Waste Valve - Black Water Tank - Spigot to Spigot - 96" Cable, part #34466N4BB96GM, needs ABS solvent cement, part #3447530889, to secure the valve to your sewer…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Replacement 3 inch Waste Valve to Replace Bristol Waste Valve

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching