Replacement Velcro For 2011 Ford F-350 Truxport Tonneau Cover

Question

Question:

I have a 2011 f350 with a long bed and it has a truxport tonneau cover. the Velcro no longer holds. Do you sell replacement Velcro?

asked by: Joe M

0

Expert Reply:

For your Truxsport Tonneau on your 2011 Ford F-350, you will want the Replacement Truxedo Shur-Bond Velcro Brand Fastener # TX1117876. This is a 1 inch wide strip of the hook side of the velcro. The mating loop piece will already be on the tonneau cover.

expert reply by: Jason S

0

Answer 1

Replacement Truxedo Shur-Bond Velcro Brand Fastener #TX1117876 slides into the bed rail channels for the Tonneau cover. It isn't an adhesive-backed model so based on your description this is the correct replacement.

view full answer...

Answer 2

Replacement TruXedo Shur-Bond Hook-And-Loop Fastener Strips #TX1117876 is the correct replacement velcro strip for your Tuxedo tonneau cover on your 2012 Dodge Ram. You will need to trim to size, as these strips are 1" wide and 80" long.…

view full answer...

Answer 3

The Replacement Truxedo Shur-Bond Velcro Brand Fastener, part #TX1117876 is designed to work with TruxSport tonneau covers only. From the photo you sent it looks like you have a Lo Pro tonneau cover on your truck. The correct replacement Velcro for…

view full answer...

Answer 4

The Replacement Truxedo Shur-Bond Velcro Brand Fastener #TX1117876 comes with two strips of Velcro. This would work for both sides of the cover. The opposite side of the Velcro will be on the tonneau cove itself.

view full answer...

Answer 5

The Replacement TruXedo Shur-Bond Hook-And-Loop Fastener for your TruXsport cover on your Toyota Tundra is 80 inches long and 1 inch wide. It is part #TX1117876.

view full answer...

Answer 6

For your Truxedo Truxport tonneau cover the correct velcro you need for the side rails is the part #TX1117876 and you'd be set. This comes with screws to install and would need to be cut down to the size you need.

view full answer...

Answer 7

To replace the Velcro strips for the TruXedo Lo Pro Tonneau Cover #TX577601 on your 2008 Ford F-150 you just need the part #TX1115174. Just keep in mind that you will need to cut the strip down to size as it's technically made for the 6-1/2 foot…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Replacement Velcro For 2011 Ford F-350 Truxport Tonneau Cover

Product Page this Question was Asked From

Continue Researching