Is Replacement Manual Cranking Hex Nut Available for Lippert Powered Tongue Jack LC285318

Question

Question:

The 3/4inch manual override nut has cracked in half on jack. Is there a replacement part for this? Thank you in advance.

asked by: Brian V

0

Expert Reply:

The manual cranking hex nut on a jack like the Lippert powered tongue jack # LC285318 is not a serviceable or replaceable part. The jack will need to be replaced.

expert reply by: Adam R

0

Answer 1

Only certain bike racks are rated by the manufacturer for use behind RVs or trailers. This is simply because the ride at the rear of an RV is significantly rougher when compared to the rear of a standard passenger vehicle. The reason for this is…

view full answer...

Answer 2

I recommend using the Swagman XTC4 4-Bike Rack for 2" Hitches - Platform Style #S64665 because the platform will keep the bikes mostly out of your field of vision better than a hanging rack would. The XTC4 is rated for use on a Class C RV…

view full answer...

Answer 3

I do not think the fuse is blown because the light still comes on. It sounds like the motor has gone out. This could happen from over extending a jack or overloading it. If the jack is connected to a battery mounted on the trailer, the battery may…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 8

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 9

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 10

As long as the flat tow wiring is wired in before the 4-Way #C93ZV and you connect the power for the converter directly to the battery it will work. I have seen several use Magnetic Lights #TL21RK which they will wire in on the main harness to have…

view full answer...

Answer 11

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 12

There are some subtle difference between the Kuat Piston Pro Bike Rack for 2 Bikes #KU76ZR and the Kuat Piston Pro X Bike Rack for 2 Bikes #KU98VR. Overall the two racks are very similar, there are just some subtle differences/upgrades on the Piston…

view full answer...