Front Mount Trailer Hitch for a 2008 Ford F-450 4x4

Question

Question:

Will it fit a 2008 F450 Super Duty crew cab with 4 wheel drive?

asked by: Robert R

1

Helpful Expert Reply:

Yes, Draw-Tite front mount receiver # 65049 will fit your 2008 Ford F-450 4x4. I have included a link to a video showing an example installation for you.

expert reply by: Michael H

1

Answer 1

We have an easy to install front hitch that fits your 2008 Ford F-250 that allows you to keep the tow hooks with the Draw Tite part #65049 but this does not attach to the tow hooks and puts the hitch opening down below the front bumper. I attached a…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

Hey Scott, If you're wanting a brake controller that will plug into your factory wiring harness and won't give you any errors then I recommend going with the Tekonsha Prodigy P3 #90195 along with the Tekonsha Plug-In Wiring Adapter #3034-P.…

view full answer...

Answer 5

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 6

Hi Kris, TorkLift lists part number #EH54QR as a fit for a 2023 Ford F-550. The #306-X7904 is not listed as a fit for an F-550 at all but we've confirmed it on our site because F-350 owners were trying it and it fit. Most likely it could fit but…

view full answer...

Answer 7

Yes, it will so long as your 2023 Ford F-350 doesn't have dual rear wheels. It won't work with the dually models since there is a larger front mounted auxiliary cooler that interferes with installation. The EcoHitch Hidden Front Hitch item…

view full answer...

Answer 8

Yes, the glass top on the Furrion 2-in-1 Range Oven #FR97KR is removable. The hinge for the glass has a small Phillips-head screw with a Phillips-head cap on it (pictured below) that can be removed to take the glass top off.

view full answer...

Answer 9

I checked with Furrion and confirmed the Furrion 2-in-1 Range Oven with Glass Cover part #FR97KR has an enamel stamped removable grate, not die cast.

view full answer...

Answer 10

I did some research and found instructions for installing the RanchHand Legend Grille Guard on your 2011 F-250 4x4. You can check out the attached photo that shows where a front hitch is mounted on a Ford F-250. You may find that the bottom bar on…

view full answer...

Answer 11

For your 2008 Ford F-350 we have the Draw Tite hitch part #65049 which is a confirmed fit and has a tongue weight capacity of 500 lbs. The motorcycle carrier we offer that would work best is the Ultra Fab part #UF48-979033. Reason being it weighs…

view full answer...

Answer 12

Pilot diameter on a wheel like our dually trailer wheel part #AM20783 that you referenced is basically the diameter of the center hole of the wheel. This wheel has a pilot diameter of 4.75 inches. I attached a picture that shows this dimension as…

view full answer...