Replacement Hitch Pin Bolt Recommendation for Older Yakima SwingDaddy

Question

Question:

I recently purchased an older model yakima swingdaddy or fullswing rack. Didnt come with a bolt for the hitch and didnt know if this one would fit. Its is for a 2inch receiver. Thank you

asked by: Mike D

0

Expert Reply:

For the older Yakima Swingdaddy bike rack that used a hitch pin bolt the correct replacement would be the part # Y8890176.

expert reply by: Jameson C

0

Answer 1

The linked page displays all Yakima replacement hitch bolts for their various bike racks. You may be able to identify the correct one for your rack by its appearance, but if not we do include the names of the compatible carriers for each one. If you…

view full answer...

Answer 2

I reached out to my contact at Yakima and their bike racks use either #Y8890176 for racks that fit a 1-1/4 inch receiver and #Y8890200 if the rack fits a 2 inch. To lock either pin use #Y07235 which attaches over the hitch pin and uses an included…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

If you want to install the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13182 on your 2016 Jeep Grand Cherokee, you will use M14 bolts that are grade 5 as well as compatible flat washers. That is the replacement for what is…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Hey Kyle, we have the Curt hitch part #C13065 that fits your 2018 Jeep Grand Cherokee Altitude which would be a really great option. It has great towing capacities and is mostly hidden.

view full answer...

Answer 10

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

The Tow Defender #RM-4700 you found is really our best option to protect the front of your 2024 Chevrolet Trax. This screen helps to deflect any road debris back down to the ground to keep it traveling under your Trax. This particular cover is…

view full answer...