What is the Mounting Hole Spacing on Curt Trailer Hitch C13333

Question

Question:

What is the distance between the mounting holes on the backside of the receiver? I want to ensure those holes will align to the holes on my tubed framing before purchase. Thank you.

asked by: Tim

0

Expert Reply:

I went out to the warehouse to measure the hole spacing on Curt trailer hitch # 13333 for you. The holes are spaced 7-3/4 inches apart on center. This is a custom fit hitch designed for the following vehicles:

2004 - 2014 Dodge Ram Pickup 1500 Series, without factory hitch
2003 - 2003 Dodge Ram Pickup 1500 Series, without factory hitch - built After 11/1/02
2003 - 2013 Dodge Ram Pickup 2500 and 3500 Series, without factory hitch
2010 - 2013 Ram 3500 Pickup, without factory hitch
2010 - 2017 Ram 1500 without factory hitch
2010 - 2013 Ram 2500 without factory hitch

expert reply by: Michael H

0

click to enlarge

Answer 1

I spoke to my contact at B and W and he said that when their hitch balls get frozen up in the hitches like the part #BWGNRK1313 the best solution is to let it soak for along time with penetrating oil like WD40 or PB blaster. He said the more…

view full answer...

Answer 2

There are absolutely plug-in wiring adapters for a brake controller for your 2020 Ram 1500, and what you can use is the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In #C51458 Then for a brake controller that doesn't take…

view full answer...

Answer 3

For your 2005 Dodge Ram 1500 Rumble Bee I recommend the Curt Trailer Hitch Receiver #C15809. This is confirmed to fit the Rumble Bee and designed to install below the factory hitch. If you want to remove the factory hitch you also have that option.…

view full answer...

Answer 4

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 5

I contacted Venture Trailers Inc. and found that the reason they do not recommend the use of a weight distribution system is because most weight distribution systems are not recommended for trailers with surge brakes because they do not allow the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

We do have a bearing with a 1.75 inch inner diameter, the Replacement Trailer Hub Bearing #25580. That said, there are numerous bearings with a 1.25 inch inner diameter, and I wouldn't be able to tell you exactly which one you need, so I've…

view full answer...

Answer 9

Hey Barbara, yes the Yakima OnRamp #Y88DJ can be used on both your camper and Highlander. It's a really great e-bike rack that is RV rated and if you wanted to add the swing away adapter you can too with the part #Y02483. It's not super hard…

view full answer...

Answer 10

I can understand why you'd think that the Curt Trailer Hitch Receiver #C13419 wouldn't be as solid and sturdy. However, the hitch receiver is designed to bolt up to your bumper beam, which is then bolted to your truck's frame on both…

view full answer...

What is the Mounting Hole Spacing on Curt Trailer Hitch C13333

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching