Replacement Threaded Screw and Pin for Thule Hitching Post Pro # TH934XTR

Question

Question:

I bought the TH934XTR in January, just completed an 8,000 mile trip to the West Coast and back! Worked great, but I noted some jiggling at times. Tightened up the main bolt and that mostly worked. But when I got home and tore down, I found that the screw that held the sleeve in place was broken off! Thought it was tight, but maybe not. At any rate, can you provide a replacement? I am going to have a struggle removing the shaft of the screw chemicals, heat, drill and easy-out???. Thanks

asked by: Patrick M

0

Expert Reply:

If you are needing the Flat Cap Screw that holds the adapter on the shank of the Thule Hitching Post Pro # TH934XTR, then you are needing part # 853-5787-02.

If what you are needing is the replacement threaded pin for the Hitching Post Pro then you will need part # 853-5917.

You can use the Ratchet with 3/4 inch Socket # PT20104-38524 to tighten the anti-rattle bolt down. This is a convenient thing to just keep in your rear cargo area so you don't have to go hunt down a wrench or socket.

An upgrade to the anti-rattle bolt is the Thule Snug-Tite Hitch Lock and Anti-Rattle Device # THSTL2 which will allow you to add some extra security to your bike rack.

Using heat and a drill can work for getting the bolt out, but be very careful not to compromise the integrity of the bike rack or your trailer hitch.

expert reply by: Jon G

0

Answer 1

For your Thule Hitching Post Pro - Folding Tilting 4 Bike Rack w Anti-Sway - 1-1/4" and 2" Hitches #TH934XTR, it sounds like you are missing the 2 inch hitch adapter. This adapter is the Replacement 2" Hitch Adapter for Thule…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The Yakima EXO Swing Away 2 Bike Rack w/ Enclosed Cargo Carrier #Y34ZR will restrict the passenger side door on your 2024 Entegra Expanse. When the arm swings out it will be sitting at that corner of the vehicle which means the door will be able to…

view full answer...

Answer 4

I confirmed with EcoHitch and their Trailer Hitch Receiver #EH39FR was just confirmed to fit your 2024 Tesla Model Y this week. This is great since the receiver opening is accessible through the rear cover plate just like a factory option.

view full answer...

Answer 5

Per the linked installation instructions which you can click below the torque is 86 ft-lbs for the 12mm hardware when installing the etrailer Trailer Hitch Receiver #e75ZR on the 2023 Toyota Highlander.

view full answer...

Answer 6

Both of these Thule racks will do an excellent job of safely and economically hauling four bikes (assuming you aren't using a Class I hitch, which has a manufacturer recommended limit of hauling two bikes at a time). The Camber #TH9056 is lighter…

view full answer...

Answer 7

Yes, the Curt cargo carrier 18153 will fit the Curt Trailer Hitch Receiver #C26VV on your 2024 Grand Highlander. The 2" shank matches the 2" receiver on the hitch.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Replacement Threaded Screw and Pin for Thule Hitching Post Pro # TH934XTR

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching