Equal-I-zer Weight Distribution with Shank for 2-1/2 Inch Hitch Receiver

Question

Question:

Can I get this, but with a 2.5inch shank instead so that I dont have to use my 2-2.5inch adapter? If yes, then what is the total cost?

asked by: Steven F

0

Expert Reply:

Yes, instead of getting the # EQ37100ET weight distribution system use part # EQ37101ET which doesn't include the shank and then add # EQ90-02-4700. This is the same shank only for a 2-1/2 inch hitch receiver.

The cost of each product is shown on our product pages.

expert reply by: Charles S

0

Answer 1

Tilting the ball, or the head, of a weight distribution system that allows it, such as #RP66074, has a couple of uses. It allows you to put the proper tension on the spring bars, crucial for proper system set up, and it can be used to help level…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 8

Welcome back! You do not need to cut anything away! So long as your 5" of clearance was measured with your trailer loaded and resting on the suspension you will be good. The SumoSprings Trailer Helper Springs item #SS26MV include spacers that…

view full answer...

Answer 9

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 10

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Answer 11

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 12

The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57531 will fit your 2022 Ram 3500 Mega Cab with single rear wheels. This is the extra heavy duty 7,500 lb kit so it is most commonly used on dually trucks, but it will fit single rear wheel models…

view full answer...