Difference Between 23-106 and 23-105 Trailer Brake Assemblies

Question

Question:

My trailer has 23-106 brakes on right side and 23-105 on the left side. Not sure what Im supposed to have on this trailer. They are Dexter P12 axles, Serial # SLR. Spindle diameter is 2-1/4. Maybe you can help me.

asked by: Craig

0

Expert Reply:

Trailer Brake Assemblies # 23-106 and # 23-105 are the same brake assembly for the right and left sides, respectively. That's the reason for the difference in part numbers.

They're 12 by 2 inch brakes for 6,000 pound axles.

expert reply by: Charles S

0

Answer 1

To find the proper replacement equalizer for your horse trailer you will need to take a couple of measurements. Measure from the center of the front hole to the center of the rear hole. Then measure from the center of the top hole down to the center…

view full answer...

Answer 2

You shouldn't loose any wheel clearance with the Dexter E-Z Flex Suspension Kit. First you will want to see which of the Equalizers you need. There is a 6,000lb Equalizers #K71-654-00 (5-5/8") and 8,000lb Equalizers #K71-655-00…

view full answer...

Answer 3

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...