Brake Controller Wiring Adapter for 2002 Ford F450 Class C Motor Home

Question

Question:

what adapter do I need for a 2002 f450 class c motor home. I think its 3035 P

asked by: Dennis P

0

Expert Reply:

The Tekonsha Wiring Adapter, part # 3035-P is the correct adapter for the 2002 F450 cab and chassis, which is the platform the motor home is built on.

I will link you to our Brake Controller FAQ page, as well as our FAQ page specifically relating to Ford trucks. Each page has additional information you might find helpful.

expert reply by: Mike L

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 5

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 6

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 7

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 8

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

From what I could find, it looks like the plug for a trailer brake controller on your 2023 Nissan Frontier is located in the same location as the 2022 model year. That is behind the side panel by the OBD connector and is likely pushed back into the…

view full answer...

Answer 11

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Brake Controller Wiring Adapter for 2002 Ford F450 Class C Motor Home

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching