Replacement Pin for a 2/-5/16 Convert-A-Ball

Question

Question:

looking for replacement slide pin for my convert a ball. need for two inch and 2 5/16 inch.

asked by: George S

0

Expert Reply:

I have a solution for you. However, the pin is not available by itself. You can get a replacement 2-5/16 inch ball the includes the pin. The part you need is # 600B.

This ball is nickel-plated for corrosion resistance.

expert reply by: Jared P

0

Answer 1

The stainless steel construction of the Convert-A-Ball Interchangeable Ball Set part #902B is going to be much more weather resistant than the nickel plated steel of the Convert-A-Ball Interchangeable Ball Set part #900B. There shouldn't be any…

view full answer...

Answer 2

The ball pin uses rubber o-rings to hold it in place, the friction holds the pin from moving. I would suggest using a ball cover for a couple reasons. First since it wraps around the ball, the pin would not be able to come out so the ball will stay…

view full answer...

Answer 3

0000 steel wool and some aluminum wheel polish would be your best option for scrubbing it off. The acid in vinegar can also help to break down aluminum oxidation as well.

view full answer...

Answer 4

It sounds like you need a ball mount with a drop of at least 8 or 9 inches. A couple options are the Curt #C45090 with 8 inches of drop and the Curt #C45112 with 10-1/4 inches of drop. Another option since you're not positive exactly how your…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 10

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 11

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Replacement Pin for a 2/-5/16 Convert-A-Ball

Product Page this Question was Asked From

Continue Researching