Replacement EZ Lube Dust Covers on Trailer Axles

Question

Question:

Need to verify which dust caps will fit a 3500lb axle trailer... my tech keeps calling them dexter and saying he wants the ones with grease fittings.

asked by: Nikki B

0

Expert Reply:

The dusts caps that fit the EZ Lube axles fit different size holes of the brake drum or hub. For example, # RG04-040 will fit EZ Lube axles with a 2 inch inner diameter.

I have linked a page that will show all the EZ lube dust caps and the different cap sizes. You will have to have your tech measure the trailer hub to figure out which cap you will need.

expert reply by: Jared P

0

Answer 1

The BD 75450 crosses over to the Dexter #8-257-5UC3 7 inch hub/drum you'd looked at. The etrailer brand #AKEBRK-2 would be a compatible replacement for your existing brake assemblies. Mounting hardware isn't included. If you…

view full answer...

Answer 2

I can help you with greasing up your EZ Lube Axle. First thing I would check would be that the grease is not coming out of the back of the axle through the seal. If this is the case you will need to replace the seal. Our tubes like #L11390 have 14…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 11

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 12

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Replacement EZ Lube Dust Covers on Trailer Axles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching