Images of Curt Class II Trailer Hitch Receiver Installed on a 2016 Lexus NX 200t
Question:
Are there any pictures of this Class II hitch installed on a Lexus NX? I have only seen the two inch Class III installed.
asked by: Greg
Expert Reply:
Unfortunately, we have not had the chance to get any photos or a video of the Curt Class II # C12143 on a 2016 Lexus NX 200t as of yet. I did grab a couple of images from the install details that I've attached. The install details are attached as well.
This hitch is confirmed to fit your Lexus.
If you're going to be towing you'll also need trailer wiring. The Curt Wiring Harness # C56268 will provide you with a 4-way trailer connector. This will power a trailer's running, brake, and turn signal lights. It installs by plugging directly into your vehicle's wiring behind trim panels on both sides of the rear cargo area in your Lexus. Then the hot lead will need to be run to the battery.
For a ball mount the Curt # C45521 is recommended. It provides either 2-5/8 inches or rise or 3-1/4 inches of drop. If this isn't the correct rise or drop you need I've linked our selection of Class II ball mounts as well as an article to help you determine the one you need.
For a hitch ball you'll need either a 2 inch, like # A-82 or 1-7/8 inch, like # A-80. Then use # F-4 for a pin and clip.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Can a CB Radio Hook Up Via the Cigarette Lighter Port Using Adapter
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Hitch Installation Tips
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: What is the Pilot Diameter on a Wheel
- Q&A: How to Measure a Trailer Wheel Pilot Hole to Choose a Replacement Center Cap
- Q&A: Recommended 1-1/4-Inch Class II Trailer Hitch for 2016 Lexus NX 200t for Use with Kuat Bike Rack
- Article: Best Bike Racks for Fat Bikes
- Q&A: Pin Dimension of Curt Hitch from Outermost Bumper of 2016 Lexus NX 200t
- Q&A: Are Curt Hitches for 2019 Lexus NX300h and 2016 Lexus NX200t Different