Inner and Outer Diameter for Hinge Pin Nipple HPN214

Question

Question:

What are the true decimal dimensions for this part? I want it to match up with what I have. ?Im trying to rebuild an existing hinge. I need the ID and the OD dimension.

asked by: Tim R

0

Expert Reply:

I went out to the warehouse with some digital calipers to measure the inner and outer diameters of Hinge Pin Nipple # HPN214. The inner diameter of the nipple is 0.52 inches. The outer diameter of the nipple is 0.754 inches. Keep in mind that due to manufacturer tolerances these measurements can vary slightly from one nipple to the next. The nipple is 2.25 inches long and that dimension would not vary much if at all from one nipple to the next or subsequent nipples manufactured in the same batch.

expert reply by: Michael H

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

We carry all sorts of RV door parts including hinges and latches that you can see on the linked pages. I included links to hinges, latches and weather-stripping like #WS1434 and vinyl trim like #CAM25103. Since trailer makers do not keep track of…

view full answer...

Answer 3

I do have an option for you but the Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate part #VGD-10-4000 does not have a spot for the factory backup camera. Therefore you would either need to find a way to mount this yourself, go without, or…

view full answer...

Answer 4

For the Edge CS2 Evolution Diesel Tuner you will need to enter the programming menu. You will turn on your vehicle without starting it. Then use the Menu button to open the main menu and scroll down with the arrow to the Programming on the screen.…

view full answer...

Answer 5

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Answer 6

The Ramp Door Hinge #PLR1902 does require welding of both portions. The tab gets welded as you stated to one side and the outside cylinders get welded to the opposite side. I've attached a couple pictures to assist.

view full answer...

Answer 7

I would love to help but we do not offer the Paneloc Heavy Duty Spring Latch part #F719-172Z105 for left hand or part #F719-182Z104 for right hand with a pin extension of more than 1-1/4". The only option you have to obtain a greater extension…

view full answer...

Answer 8

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 9

Heavy duty ramp springs #RS16933RH and #RS16933LH install on the hinge of the ramp. I have included a picture of what this looks like for you. Not all trailers are exactly the same but this should give you a general idea of how the springs install.

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

The Polar Hardware Dump Door Hinge, Steel #PLR1904-Z that you referenced does not have a weight rating. I spoke with my contact at Polar, and he confirmed that they do not have a weight rating for this hinge. The capacity of this hinge will largely…

view full answer...

Inner and Outer Diameter for Hinge Pin Nipple HPN214

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching