What is the Hitch Pin Size on the Hitch for a 2017 Toyota Tacoma

Question

Question:

Hitch pin/lock size 2017 Tacoma

asked by: George

0

Expert Reply:

On the 2017 Toyota Tacoma, the hitch pins hole diameter is 5/8 of an inch.

For that size hole, the Curt Hitch Lock # C23519 would be a great option for your Tacoma. The Curt pin will work with both 2 and 2-1/2 inch receiver openings and is constructed of sturdy stainless steel that will resist rust corrosion.

expert reply by: Jared P

0

Answer 1

For a locking hitch pin that will fit the 2" trailer hitch you have on your 2018 Toyota Tacoma TRD I recommend the Curt Trailer Hitch Receiver Lock part #C23519. This lock has a span of 3-5/8" which should be more than enough for…

view full answer...

Answer 2

The Bolt Trailer Hitch Receiver Lock, #BL7023584, will work on Toyota vehicle's that use standard cut keys. The attached photo will show you the type of keys that are compatible for the Bolt lock. If you have a center cut key for your 2017…

view full answer...

Answer 3

If you didn't have a battery used with your breakaway system there'd be nothing to power the brakes in the event of a disconnect so you couldn't use just a switch like the part #FA80-00-2040 by itself. You'd instead…

view full answer...

Answer 4

Battery life depends on so many factors that it is hard to quantify the life any given battery. I spoke with my contact at Hopkins and he stated that if the battery is stored outside he estimates a 3 to 6 month life span. If stored inside it will…

view full answer...

Answer 5

According to the specifications of the Electric A-Frame Tongue Jack, #LC285318, from Lippert, the jack motor can draw a maximum of 30 amps at 12 volts. The closer to the capacity of the jack (3,500 pounds) the more power it will draw. I have included…

view full answer...

Answer 6

Yes, it does! The Draw-Tite Hitch item #76209 has been confirmed to fit all models of the 2024 Subaru Crosstrek including the Wilderness. This hitch is custom fit and bolts to your Subaru with included hardware. If your Subaru is not a hybrid, I…

view full answer...

Answer 7

Technically, chrome is harder than stainless steel but it isn't going to be a difference between stopping a thief or not stopping one. If a thief really wants to, they'll be able to remove any lock, locks are more of a theft deterrent and…

view full answer...

Answer 8

For the 2022 Tesla Model 3 we do have a hitch with the EcoHitch part #EH84GR but the hitch you referenced does not fit as it was designed for older versions of the vehicle.

view full answer...

Answer 9

Thanks for the photo, that was a big help. And the answer is yes, your 2023 Ford F-350 Cab & Chassis is 100 percent compatible with the Curt 7-way: - Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector #C69CR…

view full answer...

Answer 10

New GM trucks don't have consistent 12 volts on their trailer wiring circuits. While this tends to not be a problem for trailer lighting it does not always work great with more sophisticated circuits like your tester. This is a big issue for…

view full answer...

Answer 11

We measured the distance from the center of the hitch pin hole to the center of the hitch ball and found that measurements was 10-1/2 inches for the Curt Ball Mount for 2-1/2" Hitches #C45460. This ball mount has a 20,000 lb capacity and gives…

view full answer...

Answer 12

The B&W Rubber Cover for Stowed Turnoverball #BWGNXA1710 will not fit on the bottom of the Turnoverball unit. You don't want moisture to be held in, so putting a plug on the underside wouldn't be recommended even if it did fit. You want…

view full answer...

What is the Hitch Pin Size on the Hitch for a 2017 Toyota Tacoma

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching