Replacement Landing Gear Motor And Gearbox For 2009 Holiday Rambler

Question

Question:

The front left motor on the jack has burned out so I know I need to replace it. However, now that I am manually jacking it, it turns substantially harder than the other side with the functional jack. Does this mean the gearbox is probably bad and the additional resistance was the cause for the burn out of the motor, or does a burned out motor cause the gearbox to turn harder in manual mode?

asked by: Terry

0

Expert Reply:

I reached out to Lippert and they confirmed my thoughts that the gearbox is most like bad since you are having trouble with the manual jack. That surely could have caused the motor to burn out. For a replacement, I recommend the Lippert Components Venture 5th Wheel RV Landing Gear Motor # LC142178 along with the Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear # LG-179015.

expert reply by: Jason S

0

Answer 1

I would recommend replacing the landing gear you have on your 2009 Holiday Rambler with a new set like the Ultra-Fab Deluxe Electric Landing Gear, part #UF17-943010. This system has a combined weight capacity of 12,000-lbs and has a retracted height…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 4

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Landing Gear Motor And Gearbox For 2009 Holiday Rambler

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching