Is E-Strap Compatible With Ford Box Link System?

Question

Question:

Will your E-strap products work with the ford box link system?

asked by: Andrew H

0

Expert Reply:

The Snap-Loc E-Track Tie-Down Strap w/ Ratchet and Soft Tie-Loop - 2" x 8' - 1,467 lbs, # SLLS28RER, as well as many other E-track products are compatible with most similar systems. I cannot confirm that these straps will work with the Ford Box Link System as we have not tested them.

expert reply by: Jason S

0

Answer 1

With the BoxLink system on your 2015 Ford F-150, you have multiple options when it comes to tie down straps. You can attach directly to the BoxLink cleats or hook directly to the interface plate with a bungee cord, S-hook, or E-track fitting. I have…

view full answer...

Answer 2

The Erickson E-Track Tie-Down Anchor #EM37JR has 5/16" holes for the grade 5 mounting hardware. Hardware is not included as you will need to ensure the hardware is the correct length for your application.

view full answer...

Answer 3

The Erickson E-Track Tie-Down Anchor #EM37JR is 5.2" Long, 5.2" wide and 0.5" tall. The two 5/16" holes are centered on each side of the of the bracket 2.75" from each other. Please see the attached image.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...