What Circuit Does the 5th Pin of the part # C56584 Carry

Question

Question:

is the 5th pin for reverse light access? I am looking to use this harness for wiring up my backup camera.. Looks like a no-splice solution...

asked by: Scott

1

Helpful Expert Reply:

Yes, the fifth pin of the Curt wiring harness part # C56584 that you referenced does carry the reverse light circuit so it would work well for you.

expert reply by: Jameson C

1

Answer 1

Yes, the 5-way that the Curt 7-way to 5-way adapter #C56584 provides does have a 5th pin that has the reverse light circuit like you are needing. So the pin on the one side of the connector that has the blue wire does carry the reverse light…

view full answer...

Answer 2

I can certainly help you with that. Since the Curt T-Connector Vehicle Wiring Harness, part #C55384 is a 4-way connector the four functions will be Yellow for the left turn and brake, Green is for right turn and brake, Brown is for running lights,…

view full answer...

Answer 3

I think I understand what you are asking. For your 2015 Jeep Cherokee, the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118605 will give you the basic trailer functions as you stated and then you can add the reverse feature alone…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

What Circuit Does the 5th Pin of the part # C56584 Carry

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching