Height of Front Legs of Lippert Ground Control 3.0

Question

Question:

LIPPERT GROUND CONTROL 3.0 Front Landing Gear Legs length with legs compressed to top of the motor where the 3/8 connection to manually operate. I want to make sure it fits in my 2006 JAYCO JAYFLIGHT 275RLS FIFTHWHEEL please. Thanks.

asked by: Curt E

0

Expert Reply:

I spoke with my contact at Lippert and she send me a dimension sheet for the front legs of the Ground Control parT # LC358590. I attached it for you to check out and compare to the trailer you have. This kit has been used on several Jayco trailers so it really should fit your trailer and work well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The distance between the insides of the weld stops on the jack leg #LC362485 is 17-1/2 inches and the outer tube diameter is 2-1/2 inch by 2-1/2 inch.

view full answer...

Answer 2

No, the hall effect motor does not have to be greased, but per the service manual if the jacks are down for an extended period, it is recommended to spray the exposed leveling jack tubes with lubricant every 3 months for protection. If you live in…

view full answer...

Answer 3

Do you get any error code on the controller for the Lippert Ground Control 3.0 #LC675817? Usually that helps to troubleshoot and the manual gives an exact solution for each error code. You might also try resetting the Zero Point Calibration to see…

view full answer...

Answer 4

In regards to the Lippert Ground Ground Control 3.0 Leveling System, if you just need a new front leg then this can be replaced with the Replacement Front Jack for Lippert Components Ground Control 3.0 Leveling System part #LC362485. If you need a…

view full answer...

Answer 5

In regards to the Lippert Ground Control 3.0 Leveling System (what you were looking at), there are no replacement inner tubes available. Therefore, if you bent the inner tube on the front leg then you will need to replace the entire leg for which…

view full answer...

Answer 6

The leveler that will work for your tri-axle trailer is the Andersen Camper Wheel Chock and Leveler #AM3604. The Rapid Jack #AM3620 will not work for multi-axle trailers because the jack is too large to fit between the tires,

view full answer...

Answer 7

The pin weight of a 5th wheel trailer will usually be around 20% of the trailer's gross trailer weight (GTW) rating. The only real way to find the loaded pin weight of your 5th wheel trailer would require access to a commercial scale used…

view full answer...

Answer 8

Sometimes the displays of the Lippert ground control systems need to be reset. Try unplugging the control panel for several seconds and then plugging it back in. We've seen just doing that alone fix most of the problems with the control…

view full answer...

Answer 9

Yes, you can up to three additional cameras to the Furrion RV Observation Camera System part #FOS05TASF. For the side of your trailer, I recommend using the Furrion Vision S Side Camera w/ Marker Light Bracket part #FCE48TASL which is also a built…

view full answer...

Answer 10

The "out of stroke" error means you have extended the jack too far. If the jack will not retract using the touchpad then you will need to do so manually with the manual override on top or bottom (see photo). If you continue to get…

view full answer...

Answer 11

Your leveling system is not supposed to lift the wheels off the ground; this could exceed the capacity of your leveling system and cause damage and I do not recommend doing so. If you can make any adjustments to the legs then you will want to go…

view full answer...

Answer 12

I reached out to Lippert to confirm that you can change out your 24-1/2" rear jacks that come with the 4-Point Lippert Ground Control 3.0 #LC358590 with the Short Left Rear Leg #LC342610 and Short Right Rear Leg #LC428493. They confirmed…

view full answer...