Needing Replacement Grease Seals for Part # TCM 171255VB

Question

Question:

I am looking for 4 seals for my trailer. TCM 171255VB Thanks.

asked by: Alan M

0

Expert Reply:

The seal that you need to replace your Transcom grease seal TCM 171255VB are the TruRyde Grease Seals # RG06-050. These are a double lip seals that are sold by the pair, so you will need to order 2 sets to get 4 total seals
.

expert reply by: Jared P

0

Answer 1

Thickness won't really matter that much. The seal #34823 is .25 inch thick but if the inside and outside diameters match what you have it will work just fine.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

If your 2020 Kia Sorento has the factory tow package, there will be a tail light wiring connector behind the rear tire of the driver side, on the outside of the frame rail. As shown in the attached photos, an underbody cover will need to be removed…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 9

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 10

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 11

Hey Dave, what you gave me is enough info to get you replacement bearings. The grease seal 471750 matches the part #TMK48ZR. For a Timken replacement for the L44610 part number you'd need #TMK63VR. Then for a bearing for the L44649 you'd want…

view full answer...

Answer 12

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Needing Replacement Grease Seals for Part # TCM 171255VB

Product Page this Question was Asked From

Continue Researching