Can Yakima FrontLoader be Installed in Reverse

Question

Question:

Hi. I have been told that the Frontloader will hit the rear hatch when the hatch is opened. If this is the case, can the frontloader be placed backwards on the racks? and is this advisable? is there any downside to having it backwards.

asked by: Brad

0

Expert Reply:

You can install the Yakima FrontLoader Wheel Mount Bike Carrier # Y02103 in reverse if you wanted to. I have actually seen people do this on the highway and it worked fine.

I attached a review video for this rack for you to check out.

expert reply by: Jameson C

0

Mark

6/16/2020

Hi, I have a 2019 Subaru Outback, flipping around the front loader (to where the front wheel is facing the backside of the car) allow the rear gate to fully open?

Reply

Chris R.

6/19/2020

When there isn't a bike loaded switching the FrontLoader orientation should allow for rear hatch clearance since the back of the rack will be pretty much even with the crossbar itself. When you load up a bike though the wheel clamp (and wheel) may interfere with the hatch.

Reply

Answer 1

Yes, you will remove the brass nut and bolt and the red knob will come off. You should note that the #8880226 does not come with a new nut (just a washer), so be sure not to lose your current one.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 9

The Malone Universal Crossbar System #MPG201 is a more economical choice but it still does a good job. The design and quality of Thule's system is why they have such a large difference in price. Whether you go with the Thule Crossroads system…

view full answer...

Answer 10

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 11

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 12

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...